Daily maintenance of cnc router machine.

Many people just want to know the 3 axis cnc router 1325 price. But, purchased, still have many problem. In order to ensure the long-term normal use of the sign 1325 cnc router wooden work, it is necessary to maintain the cnc milling machine 3 axis router equipment on a daily basis.

 

一：Spindle cooling system

 

1. Water cooling spindle

A: The spindle of the portable cnc router machine wood carving is cooled by water circulation, so it needs to be replaced frequently to ensure the cleanliness of the water.

B: Antifreeze should be used in winter when the room temperature is below 0 degrees Celsius to avoid freezing water pipes or tanks.

C：Before processing, it is necessary to check whether the water circulation is normal to prevent the spindle from being damaged due to lack of cooling.

 

2. Air cooling spindle

A：The maintenance of the air-cooled motorized spindle is relatively simple, and the air entering the motorized spindle must be clean.

B：Before working, it is necessary to check whether the spindle fan is working properly to prevent the spindle from being damaged due to lack of cooling

 

二：Lubrication system

1：Be sure to clean the dirt on the guide rails and racks before performing automatic lubrication, and then automatically lubricate the rails and racks once a week to prevent rust and serious wear of the guide rails and racks, and prolong the service life of the machine (recommended to use rail oil 48# or 68#).

 

三：Vacuum system

1：Water circulation vacuum pump

A：The water in the water tank must not be lower than the water level (the water evaporates quickly during work, and the water level will gradually drop).

B：The water in the water tank needs to be replaced once a week, and the cleanliness of the water must be ensured.

C：When the room temperature is lower than 0 degrees Celsius, coolant should be used, or, after each work, the water from the pump should be drained to prevent freezing and damage to the motor.

D：For long-term operation, the waste grease and its dirt in the bearing and accessory space should be removed and filled with new grease.

 

2：Air Pump

A：The air pump end bearing is installed in the middle of the pump cover. This air pump end bearing should be regularly added with grease (7018 high-speed grease).

B：The filter screen and muffler device at both ends of the vortex air pump should be cleaned in time according to the situation, so as not to block and affect the use.

四：Dust collector system　　

1：Vacuum cleaner fans should be regularly inspected and maintained. Bearings should be filled with lubricating butter once a week. Check whether there is anything attached to the fan blades at any time.

2：Before shutting down the vacuum cleaner of the wood cutting carving machine cnc router, close the front air outlet of the air duct, leaving 2-3 air outlets in the back, so as to remove the residual dust in the air duct, and start from the back, close a rear air outlet, open a front air outlet, and so on, concentrate the wind to remove the wind. Pipe residues are removed from the back to the front to avoid blockage of the air duct.

3：The dust in the dust storage bag of the vacuum cleaner needs to be removed regularly. When removing, check whether the dust outlet of the vacuum cleaner of the 4×8 ft cnc router is blocked. If there is, it should be removed immediately to avoid the blockage and the dust running in the central pipe.

五：Machine parts　

1：After the machine runs for a long time, the screws and couplings at the moving joints may become loose, which will affect the stability of the mechanical movement. Therefore, during the operation of the machine, it is necessary to observe whether there are abnormal noises or abnormal phenomena in the transmission parts, and find problems in time. Sturdy and maintained. At the same time, the machine should tighten the screws one by one with a tool over a period of time. The first sturdiness should be about a month after the device is used.

2：Regularly check whether the cables are worn and whether the cables of electrical components are connected tightly.

3：Regularly dust the electrical components inside the chassis to prevent damage to components caused by dust.

 

In fact, sometimes the maintenance and maintenance method is very simple, develop the awareness and habit of maintenance and maintenance, start from the details, operate and use according to the requirements of the specification, the machine can be used for a long time.